TL;DR
Ladder rungs at industrial sites lose grip from oil, moisture, chemical buildup, and constant boot traffic. To increase grip on ladder rungs, you have three main options: FRP/GRP rung covers (most durable for harsh environments), anti-slip tape (cheapest upfront but short-lived), and paint-on coatings (a middle-ground interim fix). OSHA requires post-1991 fixed metal ladder rungs to be treated for slip resistance, and Canadian provinces reference ANSI A14.3. For most industrial applications, formed rung covers offer the best long-term value.
This guide is for facility managers, safety officers, maintenance teams, and procurement buyers at industrial sites who need to solve a specific problem: slippery ladder rungs. It covers every term you will encounter when researching how to increase grip on ladder rungs at industrial sites, from grit types and friction coefficients to regulatory requirements and product comparisons. The goal is to help you pick the right solution for your environment, budget, and compliance needs.
Browse anti-slip ladder rung covers to see available sizes and pricing.
Why Ladder Rungs Lose Grip
Ladder rungs become slippery for reasons that compound over time. Moisture is the obvious one, but at industrial facilities the real culprits are oil, grease, chemical residue, and the gradual wearing of whatever surface treatment the rung originally had. Boot traffic grinds down texture. Dust and particulate settle into micro-grooves and fill them smooth. In Canadian winter conditions, frost and ice turn an already marginal rung into a genuine hazard.
Round bar-stock rungs are especially dangerous. The contact area between a boot sole and a smooth round bar is tiny, sometimes just a narrow strip a few millimeters wide. That small contact patch means even a thin film of moisture or oil can eliminate useful friction entirely.
The numbers back this up. In Canada, approximately 22,710 reported injuries result from ladder falls each year, with around 161 fatalities. Falls account for roughly 42% of all workplace deaths in sectors involving high-risk activities. And 60% of non-fatal ladder falls in construction involve wet or slippery surfaces.
In Ontario alone, WSIB reported 242 injury claims related to ladder accidents, roughly one injury every working day, averaging 29 lost work days per person. These are not abstract statistics. Each one represents a real person, a real investigation, and a real cost to the employer.
The case for improving ladder rung grip is not theoretical. It is a direct response to a documented, measurable hazard.
Glossary of Grip-Improvement Methods
When researching how to increase grip on ladder rungs at industrial sites, you will encounter several distinct product categories. Each solves the problem differently.
Ladder Rung Cover
A pre-formed shell that slides or bonds over an existing rung to add a textured, high-traction surface. Rung covers come in two main profiles: half-round (for round rungs) and channel (for square or diamond-shaped rungs). They are not load-bearing. They install over a structurally sound rung and rely on it for strength. They add traction but do not repair or replace a rung that has corroded or bent.
Most modern rung covers are made from FRP or GRP (defined below) with embedded abrasive grit. They resist corrosion, tolerate extreme temperatures, and can be cut on-site to fit non-standard rung lengths.
For a deeper look at structural considerations, see this guide on load capacity and durability of ladder rung covers.
Knurled Rung
A metal rung machined with a crosshatch or diamond-pattern texture pressed into the surface. The aggressive pattern provides exceptional traction and a comfortable grip. Knurled rungs are available in steel, stainless steel, and aluminum. This is a rung replacement, not a retrofit cover. Choosing knurled rungs means fabricating or purchasing a new ladder (or new rung sections), which makes sense for new builds but is costly for existing installations.
Twisted Rung
A metal rung formed with a continuous spiral along its length. The spiral creates multiple contact edges that improve grip compared to a smooth round bar. Like knurled rungs, twisted rungs are primarily used in new ladder fabrication rather than as a retrofit solution.
Anti-Slip Grating Rung (Grip Strut / Traction Tread)
Stamped metal rungs with serrated, dimpled, or perforated surfaces. Products like Traction Tread and Grip Strut are designed for both new ladders and retrofitting existing ones. The open design also allows water and debris to pass through rather than pooling on the rung surface. These work well in environments where standing water or ice accumulation is a concern.
If your facility also uses FRP grating on platforms near ladders, grating-style rungs offer a consistent slip-resistant surface across the entire access system.
Anti-Slip Tape
Adhesive-backed abrasive film applied directly to rungs. It is the cheapest and fastest option. Peel it off the roll, press it onto a clean rung, and you have immediate traction. But tape is a consumable. It lifts at the edges, fills with grime, and comes back onto the maintenance schedule within months. Practitioners on forums report using rubberized grip tape from hardware stores on ladders, particularly for winter conditions where snow makes rungs slick. One user on Beesource (a beekeeping forum, of all places) noted they “use it on our ladders so we don’t fall off them in winter.”
For light-duty or temporary applications, tape has its place. For industrial sites with oil, chemicals, and heavy boot traffic, it fails too fast to be a primary solution. The adhesive also struggles to bond below roughly 10°C during application, which is a real limitation in Canadian facilities.
View Gator Grip anti-slip tape for applications where tape is the right fit.
Anti-Slip Coating (Paint-On Grit)
An epoxy or polyurethane base mixed with aggregate (sand, aluminum oxide, or silicon carbide) that you brush or roll onto the rung surface. Forum users frequently suggest DIY approaches: one recommended a thick coat of epoxy spray paint with play sand sprinkled over it as a cheaper alternative to marine-grade non-skid paint. Truck bed-liner products are another popular improvisation.
These coatings work as interim solutions. They require thorough surface preparation, adequate cure time, and periodic reapplication. In high-traffic industrial zones, the coating wears through in one to three years depending on conditions. They are not a substitute for a formed cover or a knurled rung in demanding environments.
Photoluminescent Rung Cover
A rung cover with a glow-in-the-dark strip embedded in or bonded to the surface. These are critical for egress ladders in environments where power failures can leave workers in total darkness, such as marine vessels, offshore platforms, refineries, and tunnels. The photoluminescent element charges under ambient light and glows for hours after the lights go out.
For premium options with enhanced visibility, consider Hi-Traction ladder rung covers.
Key Material and Performance Terms
Understanding these terms will help you evaluate product quality when comparing ways to increase grip on ladder rungs.
FRP / GRP (Fibre Reinforced Plastic / Glass Reinforced Plastic)
The composite material used in most modern rung covers. It consists of a thermosetting resin matrix reinforced with glass fibers for strength and durability. FRP is lightweight, corrosion-proof, and can be cut on-site with standard tools. It will not rust in marine environments, will not degrade from chemical splash, and will not conduct electricity (a useful property in some industrial settings).
Quality FRP rung covers embed industrial-grade abrasive grit directly into the surface during manufacturing, so the traction is integral to the product rather than a coating that can peel away.
For more on how FRP products are manufactured, see this guide on cutting pultruded FRP on site.
Silicon Carbide and Aluminum Oxide Grit
These are the abrasive particles bonded to the surface of quality rung covers and tapes. Aluminum oxide sits at Mohs hardness 9 to 9.5. Silicon carbide is even harder. Both far exceed the hardness of typical boot sole materials, which fall in the Mohs 6 to 7 range. This hardness differential is what creates reliable traction: the grit bites into the sole material and resists the sliding force.
Industrial-grade aluminum oxide grit is typically rated at grade 16 (medium/coarse). Refined, extra-hard granules give superior performance and wear characteristics compared to cheaper fillers like sand.
Coefficient of Friction (COF)
A dimensionless number that expresses how much resistance a surface provides against sliding. A COF of 0.5, based on University of Michigan studies, is widely recommended as a guide for achieving proper slip resistance on walking and working surfaces. Metal rung covers with bonded abrasive coatings can exceed COF 0.85, well above the recommended threshold.
One important caveat: OSHA does not mandate a particular COF for walking or working surfaces and does not require employers to use COF measurement devices. The 0.5 figure is a guideline, not a legal requirement. Still, it is the benchmark most safety professionals use when evaluating products.
Pultruded
A manufacturing method where continuous fibers are pulled through a resin bath and then through a heated die to form a consistent cross-section. Pultruded FRP is stronger and more uniform than molded FRP because the fibers run continuously in the direction of pull. For rung covers, pultrusion produces a product with consistent thickness, reliable grit distribution, and predictable mechanical properties.
Rung Profiles and Sizing
Getting the profile and size right is essential when ordering rung covers to increase grip on ladder rungs at your facility.
Round Rung vs. Square Rung vs. Diamond-Shape Rung
Fixed ladders at industrial sites use different rung cross-sections. Round rungs (the most common on older ladders) require half-round covers. Square rungs and diamond-shape rungs require channel covers. Ordering the wrong profile means the cover will not seat properly and may shift under foot.
Channel Cover vs. Half-Round Cover
These are the two profile shapes for rung covers. Half-round covers wrap around round ladder rungs. Channel covers fit over square and diamond-shaped rungs. Both install over the existing rung using adhesive mastic, mechanical fasteners such as stainless steel saddle clamp assemblies, or a combination of both.
Always Measure the Actual Rung
This is a practical detail that practitioners emphasize but most competitor content misses. Mats Inc., a well-known supplier, specifically advises measuring an actual rung rather than working from the ladder’s drawings, because field-fabricated ladders vary more than paperwork suggests. A rung listed as 3/4-inch on a drawing might measure slightly larger or smaller in the field. That difference matters for cover fit.
Standard rung cover sizes typically accommodate 3/4-inch and 1-inch rungs, but always verify with a caliper or tape measure on the actual ladder.
For guidance on specifying rung covers in project documentation, see this article on how to specify ladder rung covers in drawings.
Regulatory Terms and Requirements
Regulations drive many decisions about how to increase grip on ladder rungs at industrial sites. Here are the standards you need to know.
OSHA 1926.1053(a)(6)(i)
This U.S. standard states that the rungs and steps of fixed metal ladders manufactured after March 15, 1991, must be “corrugated, knurled, dimpled, coated with skid-resistant material, or otherwise treated to minimize slipping.” OSHA also specifies that each fixed ladder must support at least 250 pounds, with rungs that are slip-resistant and spaced evenly.
Many Canadian industrial firms align their internal standards with OSHA requirements, even where provincial regulations differ.
Inspection matters too. OSHA inspection checklists require that rungs be free of excess dirt, grease, oil, or slippery material, and that surfaces be free of laceration hazards.
ANSI A14.3
The American National Standard for fixed safety ladders. Canadian provinces reference this standard for fixed ladder requirements. For example, Newfoundland and Labrador OHS regulations specifically require fixed ladders to comply with ANSI A14.3-2002.
Canadian Provincial OHS Requirements
Ladder safety regulations vary by province. Ontario legislation requires a vertical design, rest platforms no more than 9 metres apart, installation of a safety cage for heights exceeding 5 metres from the floor, and rungs spaced at regular intervals at least 15 centimetres from the wall. New Brunswick requires ladders to be clean and free from grease, maintained in safe condition, properly secured at all points, and constructed according to regulation.
The common thread across provinces: fixed ladders must provide adequate slip resistance, and employers must maintain them in safe condition. Code or accessibility claims should always be checked against the specific regulations in your project location.
The COF 0.5 Benchmark
As noted above, a coefficient of friction of 0.5 is the commonly cited guideline for slip resistance. It is not a legal mandate from OSHA or any Canadian regulatory body, but it is the number safety professionals reference when writing specifications or evaluating products. If a rung cover or surface treatment cannot meet COF 0.5, it is not adequate for industrial use.
Tape vs. Covers vs. Coatings: Quick Comparison
This is the comparison that matters most when deciding how to increase grip on ladder rungs at industrial sites. Each method has a clear use case and clear limitations.
| Factor | FRP/GRP Rung Covers | Anti-Slip Tape | Paint-On Coatings |
|---|---|---|---|
| Durability | Years (some carry 10-year warranties) | Months on ladder rungs | 1 to 3 years depending on traffic |
| Installation | Adhesive mastic bond, mechanical fastener, or both. No special tools needed. | Peel-and-stick. Requires clean, dry, warm surface. | Brush or roll. Requires surface prep and cure time. |
| Wet/Oily Performance | Excellent. Grit bites through contaminants. | Degrades. Oil migrates back to the surface and lifts the adhesive. | Moderate. Coating wears through in high-traffic zones. |
| Temperature Tolerance | Thermal shock tested from -40°F to 150°F with no cracking or melting | Adhesive fails below roughly 10°C during application | Varies by product |
| Maintenance | Minimal once installed | Frequent replacement cycle | Periodic recoating needed |
| Upfront Cost | Higher | Lowest | Mid-range |
| Lifecycle Cost | Lowest | Highest | Mid-range |
Anti-slip tape is a film with adhesive behind it, and it has a service life measured in months on a ladder. A formed cover is fastened or bonded in place as a permanent part of the ladder. That distinction is the core of the lifecycle cost argument.
When Tape Is Enough
Tape works for temporary installations, ladders that will be replaced soon, or indoor ladders in clean, dry environments with light foot traffic. It also works as a stopgap measure while you wait for rung covers to arrive.
When Tape Is Not Enough
If the ladder is outdoors, exposed to oil or chemicals, in a wet or freezing environment, or sees heavy daily use, tape will fail within months. The edges lift, grime accumulates under the adhesive, and the abrasive surface wears smooth. In these conditions, formed rung covers are the right choice.
For more on this comparison, see our guide on ladder rung covers vs. anti-slip tape.
How to Choose the Right Solution
Selecting the right method to increase grip on ladder rungs comes down to a few key decision factors.
What is the environment? Wet, oily, cold, or chemically aggressive environments demand FRP rung covers. Dry indoor settings can get by with tape or coatings.
What condition is the ladder in? If the ladder is structurally sound but the rungs are smooth, rung covers are the answer. If the rungs themselves are corroded, bent, or compromised, you need rung replacement (knurled or twisted rungs) or a new ladder entirely. Rung covers add traction to a sound ladder. They do not repair structural damage.
What is your budget and timeline? Tape is cheapest upfront and fastest to apply. Coatings are mid-range but require prep and cure time. Rung covers have the highest upfront cost but the lowest total cost of ownership over time. One manufacturer claims over 35 years of installations with no complaints or returns. Multiple suppliers offer 10-year warranties on pre-formed anti-slip rung covers.
How accessible is the ladder? If the ladder is in a confined space or requires shutdown to access, you want a solution you install once and forget. The cost of repeated access for tape replacement can dwarf the cost of covers.
Do you need visibility features? For egress ladders, power-failure scenarios, or low-light areas, photoluminescent rung covers combine traction with visibility. This is not a nice-to-have in offshore or marine environments. It is a safety requirement.
A customer review on one product page captures the typical use case: “We install anti-slip ladder rung covers on fixed ladders, especially where water, oil, or dust make things slippery.” Another noted use “especially during the winter.” These are the exact conditions where formed covers outperform every alternative.
For more on choosing anti-slip products by surface type and environment, check the anti-slip product selection guide.
Putting It All Together
Increasing grip on ladder rungs at industrial sites is not complicated, but it does require matching the right product to the right conditions. The terms in this guide, from COF and grit hardness to rung profiles and regulatory standards, are the vocabulary of that decision. Understanding them puts you in a position to write better specs, evaluate products honestly, and make purchases that hold up for years instead of months.
The pattern across every practitioner insight, regulatory standard, and product comparison points the same direction: for industrial fixed ladders exposed to real-world conditions, formed FRP rung covers with bonded abrasive grit are the most reliable way to increase grip on ladder rungs and keep them that way.
Contact Safety Step Canada for sizing help or to discuss which rung cover profile fits your ladders.
Frequently Asked Questions
How long do FRP ladder rung covers last?
Quality FRP rung covers last for years in harsh industrial environments. Some manufacturers back their products with 10-year warranties. The key factors affecting lifespan are the quality of the abrasive grit, the resin matrix, and whether the installation was done correctly on a structurally sound rung.
Can I install rung covers on any ladder?
Rung covers fit standard round, square, and diamond-profile rungs, typically in 3/4-inch and 1-inch sizes. The ladder must be structurally sound, because covers add traction but do not reinforce a corroded or damaged rung. Always measure the actual rung rather than relying on drawings.
Does OSHA require anti-slip ladder rungs?
Yes, for fixed metal ladders manufactured after March 15, 1991. OSHA 1926.1053(a)(6)(i) requires rungs to be corrugated, knurled, dimpled, coated with skid-resistant material, or otherwise treated to minimize slipping. OSHA does not specify a particular coefficient of friction, but COF 0.5 is the widely accepted benchmark.
What regulations apply in Canada?
Canadian provinces reference ANSI A14.3 for fixed ladder standards. Specific requirements vary by province. Ontario mandates safety cages for ladders exceeding 5 metres, while New Brunswick requires ladders to be clean, free from grease, and maintained in safe condition. Always check the OHS regulations for your specific province.
Is anti-slip tape good enough for industrial ladders?
For temporary fixes or indoor ladders in clean, dry environments, tape can work. For outdoor, wet, oily, or chemically exposed ladders, tape fails within months. The adhesive lifts, grime collects underneath, and the abrasive surface wears out. Formed rung covers are the better choice for industrial applications.
How do I know which rung cover profile to order?
Measure the cross-section of your actual rung. Round rungs need half-round covers. Square and diamond-shaped rungs need channel covers. Do not rely on drawings or specifications alone, as field-fabricated ladders often have slight dimensional variations. Check our FAQ page for more sizing guidance.
What grit type provides the best traction?
Aluminum oxide (Mohs 9 to 9.5) and silicon carbide (even harder) are the two industrial-grade options. Both far exceed the hardness of boot sole materials. Industrial-grade aluminum oxide at grit grade 16 (medium/coarse) is the most common choice for rung covers and delivers reliable traction even in wet or oily conditions.
Can rung covers handle extreme temperatures?
Yes. Quality FRP rung covers have been thermal shock tested from -40°F to 150°F through twenty cycles with no cracking or melting. This makes them suitable for Canadian winter conditions, desert heat, and everything in between.

